Products : Care & Maintenance : Cleaners : TileLab® NanoClean®

TileLab® NanoClean®

An abrasive cream cleaner designed to work where other cleaners won't. It utilizes nano-sized particles to penetrate into small surface pores where it can effectively work to remove surface stains and residues. Effective for cleaning all stone and tile surfaces. Also removes factory applied waxes and floor finishes, coating sealers, light grout residue (including epoxy), rubber and pencil marks, light mineral deposits, ground-in dirt and most sealer residues. NanoClean® is non-toxic, non-flammable and non-acidic.

Available in Canada only.

  WHERE TO BUY Not all products are sold at all stores. Please call the distributor to ensure product availability.
Have a question?


Key Features

  • Powerful abrasive cleaner
  • Penetrates small surface pores to remove stains


Porcelain, ceramic, polished and unpolished natural stone (such as granite, limestone, marble, slate, and travertine), grout, quarry, saltillo, terra-cotta, cement pavers, masonry surfaces, and other stone, tile and grout surfaces.


General Surface Prep

Test a small area according to application instructions to determine desired results.

Health Precautions

MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN. Wear skin and eye protection. Contains coconut oil, DEA and ethoxylated alcohol. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting, seek medical attention. KEEP OUT OF REACH OF CHILDREN

Limitations to the Product

Do not allow product to come in contact with any non-recommended surface.

Application of Product

USE CHEMICAL-RESISTANT GLOVES, such as nitrile, when handling product.

Read entire label before using. SHAKE WELL BEFORE USING. Sweep, vacuum, or dust surface to remove any loose debris. Pre-wet surface with a liberal amount of water. Apply NanoClean® directly to the wet surface. Agitate with a white nylon pad, scrub brush or scrub machine. Mop or wet vacuum up residue. Rinse thoroughly with clean water. NanoClean® can be used as a power booster, with Aqua Mix® Heavy-Duty Tile & Grout Cleaner, Stone Deep Clean, or 1&2 Deep Clean mixed according to directions. Apply chosen product to surface, add NanoClean® and agitate mixture. Continue to follow directions on the chosen product making sure a clean water rinse is the final step to remove any remaining residue.

Cleaning of equipment

Clean tools and hands with water before material dries.


  • Close container tightly after each use
  • Store in original container only
  • Store in and use in temperatures between 40°F - 90°F (4°C and 32°C)
  • Store in areas inaccessible to small children
  • Do not reuse empty container, wrap and discard in trash or recycle

Product Maintenance

Properly installed product requires no special maintenance.

Warranty Information

Product Warranty

Custom® Building Products warrants to the original consumer purchaser that its product shall be free from defects in material and workmanship under normal and proper usage for a period of one year following the date of original purchase. Custom's® sole liability under this warranty shall be limited to the replacement of the product. Some states, countries or territories do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty will not extend to any product which has been modified in any way or which has not been used in accordance with Custom's® printed instructions. Custom® makes no other warranties either expressed or implied. This warranty gives you specific legal rights, and you may have other rights that vary from state to state or from one country/territory to another.  This warranty is not transferrable.

Product Videos


Coverage Chart

SIZE Min Coverage Max Coverage
1 Quart (946 mL) 50 sq. ft. (4.75 M²)

500 sq. ft. (46.5 M²)

© 2016 Custom Building Products. All Rights Reserved.