Quality begins from the ground up.
Preparing your surface is the most critical task of any tile or stone installation. Custom Building Products offers you one source for the needs of virtually any job.
The foundation of precise tile and stone setting.
Whatever the application, CUSTOM® offers the broadest line of tile and stone setting materials in the industry to give the exact performance your job demands.
Tile grout with dependable performance and color.
Look for tile grout with rock-solid durability, consistency and the largest color palette with Custom. Our grouts are easy to work with yet deliver hard, dense joints.
Care & Maintenance
Stains can RUIN Stone & Tile.Protect Yours Now!
Stains on stone, tile or grout happen easily - and can leave permanent stains. Protect your surface against both oil-based and water-based stains with the right sealer.
Professional Solutions for Professional Results
Offering the largest selection of Sealers, Cleaners, Problem Solvers, Grout Colorant and Stone Restoration products, we provide professionals with the right tools and solutions; making us the #1 Contractor Preferred Manufacturer of Sealers and Cleaners.
CustomTech Flooring Prep
Designed for your floors.
CustomTech – the industry’s leading collection of technologically-superior, easy-to-use, professional grade subfloor preparation products designed for all types of floor coverings.
Tools & Accessories
Precision demands the best.
SuperiorBilt® Tools are professionally preferred for tile, stone and floor covering installations.
Products : Surface Prep : Waterproofing Membranes & Underlayments : Peel & Stick Primer
Peel & Stick Primer is used for the application of peel and stick mat underlayments like Crack Buster® Pro and EasyMat®. It seals porous surfaces and improves the bond of underlayments.
No current standards exist.
Installation must comply with the requirements of all applicable local, state and federal code jurisdictions.
Custom® Building Products is committed to environmental responsibility in both products produced and in manufacturing practices. Use of this product may contribute to LEED® certification.
USE CHEMICAL-RESISTANT GLOVES, such as nitrile, when handling product.
Exterior and wet areas must have proper sloping to drains. All surfaces must be structurally sound, clean, dry and free from contaminants that would prevent a good bond. Newly prepared concrete must be troweled smooth and textured to a fine broom finish and cured for 28 days. Existing surfaces must be scarified and leveled, and all defects must be repaired. Cracks exceeding 1/8" (3 mm) should be treated in accordance with TCNA F125 or TCNA F125A.
Do not bridge joints designed to experience movement. Carry these types of joints through the tile work. Clean the joint and install an open or closed cell-backer rod to the proper depth, as outlined in the Tile Council Handbook, EJ171. Next compress sealant into the joint, coating the sides and leaving the sealant flush with the surface. When the sealant is dry, place bond-breaker tape over the joint. Install the tile work onto the membrane, but do not bridge the joint. After the tile work is properly set, follow the architect's and manufacturer's instructions to fill the joint with a specified color sealant.
Wear impervious gloves and eye protection while using this product. Avoid contact with eyes or prolonged contact with skin. Wash thoroughly after handling. If eye contact occurs, rinse cautiously with water for several minutes, remove contact lenses if easy to do: continue rinsing. Immediately seek medical advice if symptoms are significant or persist. Do not take internally. KEEP OUT OF REACH OF CHILDREN.
Do not apply to frozen surfaces or when temperatures drop below 50°F (10°C).
Apply with a paint brush or short-nap roller. Apply a thin, even coat and allow to dry to a clear film before applying Crack Buster® or EasyMat® underlayments.
Allow to dry until tacky to the touch (about 30 – 45 minutes). Drying times may vary depending on air temperature and humidity.
Clean tools with soap and water.
Store in a cool dry area. Keep from freezing.
Properly installed product requires no special maintenance. Do not use as a wear surface.
1 Gallon (3.78 L) Bottles
Obtain the applicable LIMITED PRODUCT WARRANTY at www.custombuildingproducts.com/product-warranty or send a written request to Custom Building Products, Inc., Five Concourse Parkway, Atlanta, GA 30328, USA. Manufactured under the authority of Custom Building Products, Inc. © 2017 Quikrete International, Inc.
SQUARE FOOT COVERAGE PER 1 GALLON (SQUARE METER PER 3.78 L)
CUSTOM BUILDING PRODUCTS
Mailing Address Custom Building Products 7711 Center Ave. Ste 500 Huntington Beach, CA 92647
© 2018 Custom Building Products. All Rights