Quality begins from the ground up.
Preparing your surface is the most critical task of any tile or stone installation. Custom Building Products offers you one source for the needs of virtually any job.
The foundation of precise tile and stone setting.
Whatever the application, CUSTOM® offers the broadest line of tile and stone setting materials in the industry to give the exact performance your job demands.
Tile grout with dependable performance and color.
Look for tile grout with rock-solid durability, consistency and the largest color palette with Custom. Our grouts are easy to work with yet deliver hard, dense joints.
Care & Maintenance
Stains can RUIN Stone & Tile.Protect Yours Now!
Stains on stone, tile or grout happen easily - and can leave permanent stains. Protect your surface against both oil-based and water-based stains with the right sealer.
Professional Solutions for Professional Results
Offering the largest selection of Sealers, Cleaners, Problem Solvers, Grout Colorant and Stone Restoration products, we provide professionals with the right tools and solutions; making us the #1 Contractor Preferred Manufacturer of Sealers and Cleaners.
CustomTech Flooring Prep
CustomTech – the industry’s leading collection of technologically-superior, easy-to-use, professional grade subfloor preparation products designed for all types of floor coverings.
Tools & Accessories
Precision demands the best.
SuperiorBilt® Tools are professionally preferred for tile, stone and floor covering installations.
Products : CustomTech Flooring Prep : CustomTech Flooring Prep : GenPatch™ General Purpose Calcium Aluminate Based Patch
GenPatch™ is a fastsetting, calcium aluminate compound that provides a smooth finish on interior subfloors prior to the installation of a wide variety of floor coverings. Mix with water only to patch and level concrete and plywood up to 2" (50 mm) thick. Install floor coverings in just 30 – 90 minutes.
Suitable as an Underlayment for:
ASTM International (ASTM)
Resilient Floor Covering Institute (RFCI) Recommended Work Practices for Removal of Resilient Floor Coverings
Tile Council of North America (TCNA) TCNA Handbook for Ceramic Tile Installation, TCNA Method EJ171.
American National Standards Institute (ANSI) ANSI A108.01 and A108.02 of the American National Standards for the Installation of Ceramic Tile
Installation must comply with the requirements of all applicable local, state and federal code jurisdictions.
GenPatch is a blend of calcium aluminate cement, inorganic fillers and polymers.
Custom® Building Products is committed to environmental responsibility in both products produced and in manufacturing practices. Use of this product may contribute to LEED® certification.
USE CHEMICAL-RESISTANT GLOVES, such as nitrile, when handling product.
All surfaces must be structurally sound, clean, dry and free from contaminants that would prevent a good bond. Concrete must be fully cured. Refer to final flooring manufacturer's requirements for maximum moisture vapor transmission limitations. Smooth concrete surfaces, existing glazed tile, terrazzo, or polished stone may need to be roughened or scarified. For increased performance in demanding applications, concrete surfaces can be mechanically profiled and prepared by shotblasting, sandblasting, water-jetting, scarifying, diamond-grinding or other engineered approved methods (reference ICRI CSP 3 standards for acceptable profile height). Sheet vinyl must be well bonded and stripped of old finish.
Bonding to Concrete Surfaces
Contaminants or curing compounds should be mechanically removed before installation. Concrete must be free of efflorescence and not subject to moisture beyond the floor covering manufacturers' limits or hydrostatic pressure. Lightweight concrete surfaces must have a tensile strength in excess of 200 psi (1.4 n/mm²).
Bonding to OSB and Gypsum Surfaces
OSB or gypsum-based underlayments must first be treated with RedGard® Waterproofing and Crack Prevention Membrane and must obtain a minimum 2000 psi (13.8 MPa) compressive strength at the recommended cure time. The underlayment must be sufficiently dry and properly cured to the manufacturer's specifications for permanent, non-moisture permeable coverings. Surfaces must be structurally sound and subject to deflection not to exceed the current industry standards All OSB and gypsum-based underlayment surfaces to receive GenPatch must be primed with properly applied sealer or a primer coat of RedGard®, consisting of 1 part RedGard® diluted with 4 parts clean, cool water. The primer can be brushed, rolled or sprayed to achieve an even coat. Apply the primer coat to the floor at a rate of 300 ft/gallon (7.5 M/L). Drying time depends on site conditions, but is normally less than 1 hour. Extremely porous surfaces may require 2 coats.
This product contains Portland cement. Avoid eye contact or prolonged contact with skin. Wash thoroughly after handling. If eye contact occurs, flush with water for 15 minutes and consult a physician. Use with adequate ventilation; do not breathe dust and wear a NIOSH approved respirator. If ingested, do not induce vomiting; call a physician immediately.
Plywood floors, including those under resilient flooring, must be structurally sound and must meet all industry guidelines. For questions about proper subfloor installation, call Custom® Building Products.
Adhesive layers must be removed. Use extreme caution; adhesives may contain asbestos fibers. Do not sand or grind adhesive residue, as harmful dust may result. Never use adhesive removers or solvents, as they soften the adhesive and may cause it to penetrate into the concrete. Adhesive residue must be wet-scraped to the finished surface of the concrete, leaving only the transparent staining from the glue. To determine desirable results, do a test bond area before starting. Refer to the RFCI Pamphlet, "Recommended Work Practices for Removal of Resilient Floor Coverings", for further information.
Mix 1 gal (3.78 L) clean, cool water to a 25 lb (11.34 kg) bag of GenPatch or for smaller jobs, use 3 parts powder to 1 part water.
Slowly add powder to liquid while mixing with a low speed drill (300 RPM or less) and mixing paddle to a lump-free consistency. Mix amounts that can be applied in 10 minutes.
Apply material into all voids up to 1" (25 mm) thickness using a broad knife or trowel and finish flush with surface. For skim coating, use a smooth edged trowel to flatten the surface area. Only spot patching should be done on wood surfaces. If an area more than 5 ft. (1.5 M) in diameter is required, use an appropriate CustomTech™ selfleveling underlayment.
Allow to dry for 30 – 90 minutes. Drying time can vary with temperature and humidity. Test for moisture content before applying vinyl or wood flooring.
Clean with water before material dries.
Properly installed product requires no special maintenance.
25 lb (11.34 kg) Bags
Custom® Building Products warrants to the original consumer purchaser that its product shall be free from defects in material and workmanship under normal and proper usage for a period of one year following the date of original purchase. Custom's® sole liability under this warranty shall be limited to the replacement of the product. Some states, countries or territories do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty will not extend to any product which has been modified in any way or which has not been used in accordance with Custom's® printed instructions. Custom® makes no other warranties either expressed or implied. This warranty gives you specific legal rights, and you may have other rights that vary from state to state or from one country/territory to another. For details and complete warranty information, visit custombuildingproducts.com
SQUARE FOOT COVERAGE PER 25 LB BAG (SQUARE METER PER 11.34 KG)
CUSTOM BUILDING PRODUCTS
Mailing Address Custom Building Products 7711 Center Ave. Ste 500 Huntington Beach, CA 92647
© 2019 Custom Building Products. All Rights