Quality begins from the ground up.
Preparing your surface is the most critical task of any tile or stone installation. Custom Building Products offers you one source for the needs of virtually any job.
The foundation of precise tile and stone setting.
Whatever the application, CUSTOM® offers the broadest line of tile and stone setting materials in the industry to give the exact performance your job demands.
Tile grout with dependable performance and color.
Look for tile grout with rock-solid durability, consistency and the largest color palette with Custom. Our grouts are easy to work with yet deliver hard, dense joints.
Care & Maintenance
Stains can RUIN Stone & Tile.Protect Yours Now!
Stains on stone, tile or grout happen easily - and can leave permanent stains. Protect your surface against both oil-based and water-based stains with the right sealer.
Professional Solutions for Professional Results
Offering the largest selection of Sealers, Cleaners, Problem Solvers, Grout Colorant and Stone Restoration products, we provide professionals with the tools and solutions needed to stake their reputations on; making us the #1 Contractor Preferred Manufacturer of Sealers and Cleaners.
CustomTech Flooring Prep
Designed for your floors.
CustomTech – the industry’s leading collection of technologically-superior, easy-to-use, professional grade subfloor preparation products designed for all types of floor coverings.
Flooring Installation Systems
Start with a strong foundation.
Increase the durability of your floor covering installation by ensuring that your subfloor is properly prepared. CUSTOM® Flooring Installation Systems provide a strong foundation for virtually any project, and deliver optimum performance when used under all types of floor coverings: carpet, wood, vinyl and more.
Profiles & Transitions
Discover a better choice in high-quality profiles and transitions. Create stunning designs in tile and stone without unsightly edges.
A complete line of high performing, aesthetically pleasing edge-protection profiles. Available in the most popular designs and styles, they integrate with most field tile to increase design flexibility and minimize safety risks.
Tools & Accessories
Precision demands the best.
SuperiorBilt® Tools are professionally preferred for tile, stone and floor covering installations.
Products : Flooring Installation Systems : Priming : CP-E 100%-Solids Epoxy Primer
CP-E is a low-viscosity, two-component, 100%-solids epoxy primer for surface preparation before installing an appropriate Custom® underlayment. CP-E can be used over concrete and nonporous substrates for underlayment installation, as it penetrates the surface and makes for easy installation. CP-E seals and improves that bond of the leveling system.
For professional use only.
Installation must comply with the requirements of all applicable local, state and federal code jurisdictions.
Epoxy Resin and Hardener
Surfaces must be structurally sound, clean, dry and free from grease, oil, dirt, curing compounds, sealers, adhesives or any other contaminant that would prevent a good bond. Refer to the appropriate Custom® self-leveling underlayment technical data sheet for details on bonding to specific substrates.
Avoid breathing of vapors. Forced local exhaust is recommended to effectively minimize exposure. NIOSH approved, organic vapor respirators and forced exhaust are recommended for confined areas, or when conditions may cause high concentration of vapors Hazardous vapors are released when the epoxy is burned. Avoid skin and eye contact. Wash skin with soap and water if contact occurs. If eye contact occurs flush with water for 15 minutes and obtain medical attention. Read and understand all cautions on label and MSDS before using this material.
CP-E is a two component system. Both components (liquids A and B) should be at 70-90°F (21-32°C) prior to mixing. Pour the hardener (Component B) into the resin (Component A) and blend thoroughly using a mixing paddle and slow speed hand drill for 3 minutes. Do not mix at speeds greater than 850 rpm to avoid air entrainment. Do not mix more material than can be used within 30 minutes (working time will be reduced at higher temperatures).
USE CHEMICAL-RESISTANT GLOVES, such as nitrile, when handling product.
Immediately empty the entire content of mixing container on floor. CP-E can be applied by notched squeegee and back roll with short nap roller. Finished coat should be 8-10 mils thick Make sure that there are no voids or pinholes in the coating. While this coat is still in a fresh state (maximum 30 minutes), broadcast fine, oven dried, graded 30 mesh sand to rejection (generally 1 lb/sq ft) over the entire area. When broadcasting the sand, use a NIOSH- approved dust mask. Do not stand or walk on the freshly applied epoxy when broadcasting the sand. Once the sand broadcast is complete, avoid all traffic over the surface for a minimum of 6 hours.
After 16 hours, broom sweep and vacuum the surface to remove all loose sand. The clean, prepared surface of the sand is now ready to accept Tech Level Underlayment; no additional priming is required. If the underlayment will not be installed immediately, protect its surface from construction traffic, dirt and debris. Install Tech Level Underlayment in accordance with the printed instructions.
Clean equipment before material cures. Cured material can only be removed mechanically.
Properly installed product requires no special maintenance.
Custom® Building Products warrants to the original consumer purchaser that its product shall be free from defects in material and workmanship under normal and proper usage for a period of one year following the date of original purchase. Custom's® sole liability under this warranty shall be limited to the replacement of the product. Some states, countries or territories do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty will not extend to any product which has been modified in any way or which has not been used in accordance with Custom's® printed instructions. Custom® makes no other warranties either expressed or implied. This warranty gives you specific legal rights, and you may have other rights that vary from state to state or from one country/territory to another. This warranty is not transferrable.
CUSTOM BUILDING PRODUCTS
Mailing Address Custom Building Products 7711 Center Ave. Ste 500 Huntington Beach, CA 92647
© 2016 Custom Building Products. All Rights
Contact | Careers | Terms | Privacy | Sitemap